A sample evaluation should confirm that an RGB laser projector can deliver the optical output, scanning quality, control response, safety performance, and environmental durability required for the final installation. Before approving a bulk order, test the laser power, RGB wavelengths, beam characteristics, scanning system, control interfaces, IP66 protection, safety functions, operating stability, and aging performance. The sample should also be checked against the documented configuration for outdoor concerts, stage productions, entertainment venues, or architectural applications.
Begin by comparing the physical sample, technical documents, and proposed bulk-order specification. The evaluation should cover the following areas:
The projector uses an imported semiconductor solid-state laser with analog modulation. Available configurations are listed as RGB 50W, 60W, and 80W. Measure the actual output of each color channel and compare the results with the configuration selected for the order. The stated wavelength specifications are red at 636±5nm, green at 525±5nm, and blue at 455±5nm.
Examine the aperture and optical path for a clean, stable beam. The documented beam size is <8*9mm, while beam divergence is specified as <1.2mrad. Observe whether the beam remains uniform during effect changes, color mixing, and extended operation. Any visible fluctuation in color balance, beam shape, or brightness should be recorded and discussed before production approval.
The scanning system is rated for 25KPPS high-speed scanning. Test movement smoothness, image geometry, beam positioning, and the repeatability of projected effects at different patterns and operating speeds. Include a long-duration run in the assessment to identify heat-related changes, output instability, or inconsistent effects. A French stage production company has reported stable output and consistent effects during long-hour use of supplied lighting equipment, but the approved sample should still be tested under the buyer's own operating conditions.
Test each available control route rather than relying only on the supplier's specification sheet. Use the RJ45 and ILDA DB25 interfaces, then verify international DMX512 control, self-walk operation, and master-slave synchronization. Confirm that the projector responds correctly to the intended controller or software, including Pangolin and tiger, pearl, or MA systems where applicable. Check signal loss behavior as well as normal effect selection and parameter changes.
Verify that the light source shuts down correctly when the control signal is removed or interrupted. The documented safety features include no-signal light closure and one-beam protection. Test these functions repeatedly and document the response time, reset behavior, and any conditions under which the projector could continue emitting light.
For outdoor projects, inspect the enclosure, seals, connectors, and cable entries, and request the supplier's waterproof and safety testing records supporting the IP66 protection claim. The quality process is also described as including laser module inspection, optical performance testing, scanner system testing, electronic component inspection, control system testing, aging testing, finished-product inspection, and pre-shipment inspection. These records should be matched to the sample and the configuration intended for the bulk order.
The projector is supplied in a flight case. Inspect the sample for transport damage, confirm that the packing arrangement protects the optical and electronic components, and check that all operating accessories are included. Record the serial number, measured performance, software or controller settings, accessories, and any customized features. The bulk-order specification should be approved only after these details match the tested sample.
NewFeel Lighting holds CE certification for laser light under certificate number UTT202406076C, with applicability listed as worldwide. The company has also supplied RGB laser lights, fog machines, and special-effects equipment to a United States lighting equipment distributor for wedding events, private parties, DJ performances, and small entertainment venues.
| Evaluation Category | What to Test | Approval Requirement |
|---|---|---|
| Optical configuration | RGB power, wavelengths, analog modulation, beam size, and beam divergence | Measured values correspond to the ordered specification |
| Scanning system | 25KPPS scanning speed, movement, image quality, and effect consistency | Stable, repeatable effects during normal and extended operation |
| Control integration | ILDA, DMX512, self-walk, master-slave, RJ45, and ILDA DB25 | All required modes operate correctly with the planned control equipment |
| Laser safety | One-beam protection and shutdown after signal loss | Safety responses perform according to the documented design |
| Environmental protection | IP66 enclosure, waterproof testing, connectors, and outdoor operation | The unit is appropriate for the intended installation conditions |
| Production consistency | Sample configuration, flight case, accessories, inspection records, and aging results | The approved sample becomes the reference for bulk production |
Measure the selected laser power, red, green, and blue wavelengths, beam size, beam divergence, color balance, and analog modulation behavior. The listed options are 50W, 60W, and 80W, with red at 636±5nm, green at 525±5nm, blue at 455±5nm, beam size below <8*9mm, and beam divergence below <1.2mrad.
Connect the sample through the required interfaces and test ILDA, DMX512, self-walk, and master-slave modes. Verify effect triggering, parameter adjustment, synchronization, and signal-loss behavior with the actual control equipment. Pangolin software and tiger, pearl, or MA controllers should be included when they are part of the planned system.
The stated minimum order quantity is one unit. Sample orders are listed at 7–15 working days, while bulk orders are listed at 20–35 working days after order confirmation. Customized laser system schedules depend on the selected configuration and project requirements. Available support includes technical consultation, setup guidance, software configuration, installation assistance, troubleshooting, and spare parts service.
An RGB laser projector should pass optical, scanning, control, safety, waterproof, aging, and long-hour operating tests before a bulk order is released. Keep a written record of the approved sample's configuration and measured results so production units can be checked against the same standard. Guangzhou New Feel Lighting And Audio Equipment Co., Ltd. provides R&D, manufacturing, export, OEM/ODM, and customized stage-lighting solutions, with a stated monthly capacity of 5,000 professional lighting units. For technical solutions or product support, contact sunny@nfstagelight.com.
Guangzhou New Feel Lighting And Audio Equipment Co., Ltd., trading under the NewFeel Lighting brand, was founded in 2008 in Guangzhou, China. The manufacturer supplies RGB laser projectors, outdoor laser projectors, moving head lights, fog machines, snow machines, and professional stage-effects equipment for concerts, festivals, weddings, clubs, entertainment venues, rental productions, and architectural lighting projects. Its R&D capabilities cover optical design, electronic control, structural optimization, and customized product development. Factory capacity is stated at approximately 5,000 or more lighting units per month, and its CE-certified laser products and project experience support customers in several entertainment and event markets.

REPORT